+86 731-86171990
新闻中心

Support

搜索
Search

Firstrate level transmitter common problem

(Summary description)1. How does the FST700-101 submersible liquid level transmitter measure the liquid level depth corresponding to the pressure range of the sensor? Answer: According to the pressure unit conversion table: 15℃mmH2O=0.00979Kpa is approximately equal to 0.01Kpa, and then 1M=1000mm, after conversion, the pressure range of 1M water depth=10Kpa is measured. Similarly, the range of 10M=100Kpa 20M=200Kpa is used for conversion.   2. Does the measured value of FST700-101 input type liquid level transmitter deviate from the actual value? Answer: The deviation of the measured value is roughly as follows:        A. The water inlet hole of the sensor is blocked;        B. Whether the air guide hole on the cable is blocked;        C. Sensor failure;   3. The output signal of the capacitive liquid level transmitter is unstable? Answer: The signal output is unstable:        A. The medium measured by the transmitter fluctuates;        B. The transmitter wiring is not tied;        C. The anti-interference ability of the liquid level transmitter is not strong (confirm whether there are interference sources around, such as motors, inverters, etc.);        D. The transmitter wiring is not tied;        E. Transmitter failure;   4. FST700-204 capacitive intelligent oil level sensor signal output type and calibration method? Answer: There are two output modes of intelligent oil level sensor: analog type and digital type;       Analog type sub-voltage 0-5V/0-10V, current 4-20mA;       The digital type is RS232 and RS485;       Calibration method: The analog type is external wire calibration (the zero point and full-scale wire are respectively short-circuited to ground, and the zero point and full-scale are calibrated);       Digital type is digital communication calibration;       (Specifically according to our product manual, there are detailed instructions)   5. There is no signal output from the capacitive water level sensor? Answer: No signal output situation:        A. Wrong wiring (check the wiring of the sensor);        B. The wire itself is open or short-circuited;        C. The power supply has no output or the power supply does not match (check whether the input power supply meets the power supply range);        D. The sensor is damaged;

Firstrate level transmitter common problem

(Summary description)1. How does the FST700-101 submersible liquid level transmitter measure the liquid level depth corresponding to the pressure range of the sensor?

Answer: According to the pressure unit conversion table: 15℃mmH2O=0.00979Kpa is approximately equal to 0.01Kpa, and then 1M=1000mm, after conversion, the pressure range of 1M water depth=10Kpa is measured. Similarly, the range of 10M=100Kpa 20M=200Kpa is used for conversion.

 

2. Does the measured value of FST700-101 input type liquid level transmitter deviate from the actual value?

Answer: The deviation of the measured value is roughly as follows:

       A. The water inlet hole of the sensor is blocked;

       B. Whether the air guide hole on the cable is blocked;

       C. Sensor failure;

 

3. The output signal of the capacitive liquid level transmitter is unstable?

Answer: The signal output is unstable:

       A. The medium measured by the transmitter fluctuates;

       B. The transmitter wiring is not tied;

       C. The anti-interference ability of the liquid level transmitter is not strong (confirm whether there are interference sources around, such as motors, inverters, etc.);

       D. The transmitter wiring is not tied;

       E. Transmitter failure;

 

4. FST700-204 capacitive intelligent oil level sensor signal output type and calibration method?

Answer: There are two output modes of intelligent oil level sensor: analog type and digital type;

      Analog type sub-voltage 0-5V/0-10V, current 4-20mA;

      The digital type is RS232 and RS485;

      Calibration method: The analog type is external wire calibration (the zero point and full-scale wire are respectively short-circuited to ground, and the zero point and full-scale are calibrated);

      Digital type is digital communication calibration;

      (Specifically according to our product manual, there are detailed instructions)

 

5. There is no signal output from the capacitive water level sensor?

Answer: No signal output situation:

       A. Wrong wiring (check the wiring of the sensor);

       B. The wire itself is open or short-circuited;

       C. The power supply has no output or the power supply does not match (check whether the input power supply meets the power supply range);

       D. The sensor is damaged;

Information
1. How does the FST700-101 submersible liquid level transmitter measure the liquid level depth corresponding to the pressure range of the sensor?
Answer: According to the pressure unit conversion table: 15℃mmH2O=0.00979Kpa is approximately equal to 0.01Kpa, and then 1M=1000mm, after conversion, the pressure range of 1M water depth=10Kpa is measured. Similarly, the range of 10M=100Kpa 20M=200Kpa is used for conversion.
 
2. Does the measured value of FST700-101 input type liquid level transmitter deviate from the actual value?
Answer: The deviation of the measured value is roughly as follows:
       A. The water inlet hole of the sensor is blocked;
       B. Whether the air guide hole on the cable is blocked;
       C. Sensor failure;
 
3. The output signal of the capacitive liquid level transmitter is unstable?
Answer: The signal output is unstable:
       A. The medium measured by the transmitter fluctuates;
       B. The transmitter wiring is not tied;
       C. The anti-interference ability of the liquid level transmitter is not strong (confirm whether there are interference sources around, such as motors, inverters, etc.);
       D. The transmitter wiring is not tied;
       E. Transmitter failure;
 
4. FST700-204 capacitive intelligent oil level sensor signal output type and calibration method?
Answer: There are two output modes of intelligent oil level sensor: analog type and digital type;
      Analog type sub-voltage 0-5V/0-10V, current 4-20mA;
      The digital type is RS232 and RS485;
      Calibration method: The analog type is external wire calibration (the zero point and full-scale wire are respectively short-circuited to ground, and the zero point and full-scale are calibrated);
      Digital type is digital communication calibration;
      (Specifically according to our product manual, there are detailed instructions)
 
5. There is no signal output from the capacitive water level sensor?
Answer: No signal output situation:
       A. Wrong wiring (check the wiring of the sensor);
       B. The wire itself is open or short-circuited;
       C. The power supply has no output or the power supply does not match (check whether the input power supply meets the power supply range);
       D. The sensor is damaged;

Links: Hunan Yuanhang Holdings    Hunan Aotong Intelligence 

Contact us
Tel:
+86 731-86171990
Email:sales@firstsensor.com.cn
Address: 4th Floor, Building 1, Zhitingyuan, Zhenhua Road, Yuhua District, Changsha City, Hunan Province,China.

wechat

WeChat